The regulation that requires a dashboard tire pressure monitor system in passenger cars, light trucks and vans appears to be working. This is one government directive that offers benefits to automotive consumers without significant increases to manufacturing costs. However the same cannot be said for independent tire dealers who will see operational cost increases from obtaining the automotive technology and training their employee’s on it.

Also to be considered is the time involved in accommodating tire replacement on vehicles that have the tire pressure monitor system or tire warning lights installed. Tire dealers will have to make an initial investment of about $1500 per location in equipment such as electronic scanning resetting tools and then another $200-$400 yearly for software upgrades and new equipment. Most importantly tire dealers and technicians will have to spend more shop time on tire replacement and even rotation of tires.

The tire pressure monitor system components are vulnerable to breakage if handled incorrectly or too hastily. For example a particularly breakage prone area is the air pressure sensor mounted on the inside base of the valve stem. The sensor is connected to a tiny radio transmitter powered by a long life lithium ion battery, which transmits information to dashboard readouts that signal tire under inflation. The system is designed to warn the driver, by buzzer or flashing light, when a tire has deflated to 25% less than recommended inflation pressure.

When it comes to handling an assembly with a valve stem mounted sensor, speed is the last thing on the list. The tire pressure sensor is very vulnerable. The process of mounting any tire on a wheel with a valve stem mounted sensor is slow and cautious or breakage of the sensor is a likely scenario. It should be the tire dealers responsibility to repair any damage caused by their technicians.

Tire pressure monitoring systems began appearing on passenger cars and light trucks in the 2005 model year. Following a congressional mandate requiring them on all vehicles weighing less than 10,000 pounds, by the 2008 model year. Most pickups, light duty vans, and SUVs fit into this weight category. This is why most automobile manufacturers installed tire pressure monitors systems well ahead of the September 7, 2007 deadline for compliance.

Major vehicle manufacturers and tire dealers reported no negative affects to equipping vehicles with tire pressure sensors. The national Highway traffic safety administration proposed the system after a 2001 Hwy study. The study tested 11,000 vehicles and found that 29% of the light trucks and cars had at least one tire under inflated by 25% or more.

Under inflation can cause loss of control, hydro planing on wet pavement, longer stopping distances and outright tire failure. Properly inflated tires produced better fuel economy and longer tire life, all vehicle tire manufacturers agree with this fact.

On the 2009 Silverado and Sierra pickups made by General Motors, the tire pressure warning light is in the driver information Center, located just beneath the speedometer. This system also provides the actual pounds per square inch reading for each tire. If a tire were to go below the safe pressure, a warning message would appear in the driver information center.

The tire pressure monitor system has many benefits identified by the manufacturers of these vehicles. The key benefits include improved handling as well as fuel efficiency and the ability of the vehicle to carry loads up to its recommended limits. Properly inflated tires wear more evenly across the tread contact area. They also provide greater traction and are better able to resist road hazards like nails.

Tire dealers agree that the tire pressure sensing system will help customers enjoy the performance that manufacturers design into their tires, which is severely compromised by under inflation. If tire pressure monitors systems lead to better pressure maintenance, tire performance will benefit.

Need information on how to reset tire warning lights on your car?

What is the drivers responsibility? Skeptics have questioned whether drivers will heed the tire pressure monitors system dashboard warning message. But the national Highway traffic and safety administration predicts 90% will comply with the warning message.

The convenience of being able to instantly read tire pressure on the dashboard instead of individually checking tire pressure with the old-fashioned tire pressure gauge is a huge benefit. By maintaining proper tire pressure, drivers also will enjoy extended tire life. Though the tire pressure monitor system cannot force drivers to comply. The bright tire pressure warning light will push them toward at least checking tire inflation levels.

View the original article here

The charging system usually include a method to generate electricity and store a battery for power. This sounds easy, but it is no longer a simple system. The typical system consists of a generator, which normally belt driven by the engine. The generator of this park must be regulated to control the voltage with in a given area. The usual is 12 volts to about 14.2 volts. If the voltage is too high or too low electronic and electrical components will not work or they can be damaged.

Each generator is a form of electronic controller that controls the output of the generator. In recent years, it was a regulator mounted in the vehicle regardless of the alternator. A few years ago the regulator was moved into the alternator and the system was known internally regulated. A few manufacturers decided that the electrical system should be using the computer network interface. Now most cars either the charging system is a computer or monitor and there are certain levels by the engine management computer. Many systems reduce the alternator load during periods of strong acceleration.

Can I test and diagnose problems with my generator? It depends on the equipment you have. A good multimeter will receive a fair overview of the state of a charging system. If all you have is a multi-meter to measure the voltage at the battery terminals before starting the engine. Then you measure the voltage with thethe engine is running on a fast idle. The resting tension was in the vicinity of 12.6 volts and the voltage typically ranges from 13.2 to 14.2 volts at the battery. You can also measure the output voltage of the alternator, and it should be the measure in the 0.1 volt battery voltage. After measuring the voltage at a fast idle, turn off all accessories and lights. The tension should be near the same as for a fast idle with about 3 or 4 tenths volts.

Read more…

Here, you’ll be needing your newly bought car stereo, wiring kits for adapters, wire crimping tools, tape, cutters, screwdriver/s. The features of your new stereo will depend on your choice, personality, or the whole environment of your car.

Use a wiring kit to save you an hour from your installing time, minus the frustrations.

You have to first remove the trim panels then remove the trim around the stereo. Some cars have a lot of panels to get to the stereo itself. These panels are always attached by screws. Some as visible and others need proper focus to see it. Either way, you have to carefully remove these and put them in some place where you can easily find it. Do not lose something as important as these.

We go to the portion where you remove the stereo from its nesting point. With everything out, all you need to do is carefully detach your old stereo. Again, this would be held by numerous screws so get your screwdrivers ready. After successfully getting it out, don’t just plug the new one in. There are still tasks you have to accomplish like connecting the wires altogether with the harness.

Alright, now here’s the hard part. For you to connect the adapter, you have to crimp its connections by stripping the wires. Do not try installing a stereo with only electrical tape to connect it, like twisting it together. Refer to the manual provided with the stereo. Now that you have it done, you can plug the adapter into the harness and do a test run. If all seems okay, you can now re-install all those panels that you just detached.

Finish your installation by securing your new stereo into the dashboard bracket. Arrange the electrical wirings back in its place. Then safely push your stereo back into the area. All done! Now you can enjoy a more convenient way of listening to your music.

Article sponsored by: www.jimmysautoservices.com

The situations are too numerous to count. You could endure a flat during blistering winds. Your automobile can experience overheating on a rainy evening. Whatever fate brings, you have to be prepared. This will be for the sake of your family and your car as well.

You can assemble your own kit or you can choose to buy one only at a low cost. Either of the two, you must remember that your kit must be complete and useful at anytime and any status that may take place.

A car emergency kit doesn’t take too much space. If you decided to buy one, you would expect a first aid kit together with things like ropes, cables, a funnel, batteries, a flashlight, blanket, flags, gloves, water bag, zip ties and puncture repair for your tires. These are some of the things that you would need but not entirely the things that would be a big help when trouble comes. You may also want to include medicines in your first aid kit.

Now, if you have decided to construct your own emergency kit, it must contain, not all, but some of the things already mentioned above and if you’re not satisfied about it, you could include some of your personalized ones. Some who assemble their own kits put in packs of munchies, pain killers and fever relievers. You might also want to know some of your family members opinions as well.

It is better to be safe than sorry. If the situation calls for certain measures, answer it back with a straight face and don’t fall. An emergency is always there to boost your senses until rescue or help comes in.

Article sponsored by: www.jimmysautoservices.com

If you’ve encountered an accident where it has damaged a large body panel, you may be able to pull the dent back out. All you need to do is dump soapy water over the affected area and stick a household plunger on it. After that, gently pull the plunger in order to pull the panel back into shape. The water will be able to help with the suction and the soap will be able to allow you to slide the plunger down the panel to break the suction.

However, if the accident resulted in a small dent near a creased area of the car, you will need to place a small block of wood at the tip of the dent. Then, you will need to gently tap the wood with a mallet in order to force the misplaced metal back into its original shape.

Scratches and chips on the finish are also very easy to fix. All you need to do is purchase a bottle of touch up paint with the same color of the finish of your car.

The first step is to wash the scraped area with the soapy water. Pay close attention to tar and bugs on the affected area and make sure that you remove them. Then, wet a fine grit sandpaper and carefully sand out the edges of the scraped area. After that, you need to dry the area and let it sit for at least 10 to 15 minutes or up until the area is completely dried. After this, spray the area with your bottle of touch up paint. You can apply a second coat after the first coat dries up.

As you can see, repairing minor scratches and dents are easy to do. You don’t need to spend hundreds of dollars on repairs to get it fixed. By following these tips, you can be sure that you will be able to repair minor dents and scratches from your car effectively.

Article sponsored by: www.jimmysautoservices.com

You can’t always expect for all these technologies to help you. Sometimes these things are absent when you need them most. Alright, if you’re convinced, here are the things that would help you understand that safety is not only in the hands of the car but the owner as well.

Fact is, you alone, are responsible for whatever the outcome may be. And you, above all else should know how your car would react in some predicaments. If you are just a beginner when it comes to handling cars, better consult someone who knows, someone who wouldn’t charge you for a simple question.

When it comes to doing it alone, always remember that your car is a large container of flammable liquid. It would explode if it has encountered flame or a slight spark. So be cautious NOT to burn your car down or your house. Be responsible enough to know that.

If only you know how to keep your tools away from the reach of little kids, then everyone will be happy. You wouldn’t want to hear your car cry because a bolt is missing.

Safety kits are there just in case. But that doesn’t necessarily mean that you would abuse the use of it.

Organize yourself. Never lose your concentration on what you’re doing. Always stay focused and remember the tools you used. As much as possible, do not take everything out of the box. Just those that you need are fine. Then put them back where they belong.

See, if you could only gather up that composure and earn yourself a bit of self responsibility, everything would turn out nice and smooth.

Article sponsored by: www.jimmysautoservices.com

In some way, this task is quite easy especially for those who have experienced changing one. But if you are new at this, here are simple steps to guide you. Take note, if you see that your battery has suffered corrosion severely, better let the professionals do it. But if there are no extra problems, might as well get on with it.

The first thing that you have to do is buy the correct battery for your car. You have to distinguish the right type and the typical size. If you have no idea what your battery must be, better bring your old battery and let the car parts personnel do the picking. It is advisable to buy some latex gloves and glasses to protect your hands and eyes from any spills.

If you have the habit of smoking, sacrifice for a moment. It is not a very good idea to smoke while working. Never let sparks or flames be near a spark. If possible your area should be well ventilated. Now that you’re all set, you should follow the instructions below.

1. Before disconnecting the positive cable you must see to it that the negative cable is unplugged first.

2. Remove battery connection like the hold down.

3. Once you have proven all attachments are removed, carefully lift your old battery from its tray.

4. If you see signs of rust or corrosions, clean it with water and after it dries, spray some primer to prevent further damage.

5. After that put your old battery in a safe place where no one will be exposed to it. Place your newly bought battery in the tray then clamp it. Brush the dirt off it.

6. Upon attaching the cables, you should first attach the positive then the negative cable. Tighten them to ensure that the battery stays in place.

Article sponsored by: www.jimmysautoservices.com

2. Disconnect your battery the moment you’ve decided to look at your engine. It is advisable to observe your cars inner portion if you want to assess what causes the damage internally.

3. Please, do not touch the metal parts of the car that conducts heat and electricity the moment you turn your car off.

4. Avoid smoking near the fuel system. You don’t want to put your car into flames now, do you?

5. When things just don’t turn out the way you wanted it, don’t lose track of your patience. Always keep a cool phase. Your temper can never fix the problems of your car.

6. Use extreme caution when opening the car radiator. This tends to burn your skin or anyone who’s watching you work.

7. Never blame the engine for a faulty performance. Oftentimes the malfunctioned engine is caused by the owners mishandling. Others who are jammed into a terrible car imperfection beat their car. The more it will be in a mess.

8. Whatever liquid that you extract from your car, throw it away safely that no one in the family might come in contact with it. Not even your plants or your pets can endure the chemicals embedded with the content.

9. Be careful with the things you put in your car. Sometimes, those that are little are the ones that make it work. Place the bolts and screws somewhere safe. You could use your pockets as a temporary reservoir.

10. If not in an emergency status, always park your car where no one can bother you or be bothered. Before turning the engine off, put it in a neutral status so that when you start your car, it won’t jolt. When you think everything’s safe, start working on your problem.

Article sponsored by: www.jimmysautoservices.com

First things first. You have to cool down your engine. You don’t want to experience being burned by your coolant! When everything’s the way it should be, you can remove the cap of your radiator and let it drain. Be sure the receptacle catches the coolant so that things won’t get messy and it won’t take up much of your time to clean it up. Coolant can be toxic especially to animals because of its sweet appealing taste that can cost them their furry lives.

Once the last drop of coolant had been drained, replace the plug then remove the cap. Fill it with the radiator flush solution and add water. Put the cap back on then start the car. Engage your heater at the hottest temperature and let it run for about 5-10 minutes. Do not put off the heater just yet. After a good 10-minute run, turn your car off and wait until it gets cool again.

This is your radiator flush. Now all you need to do is make a refill for your radiator flush to complete the task.

Get your fresh coolant. Replace the drain plugs. Use a funnel to eliminate unwanted spills straight through the receptacle. Mix a half solution of water with a half solution of coolant. Close the cap and tighten it to ensure spills can be prevented. Use your rags to clean up some dirty surfaces.

Now you can go to sleep without worrying that the next day would turn out like it is right now.

Article sponsored by: www.jimmysautoservices.com

To open the filter housing, you need to flip the metal clips downward. If it is too tight to do by hand, you will need the help of a flat head screwdriver to pop it off. There are some housings that will also have a nut holding it on the top.

After removing the nuts of your filter housing, it is important that you should keep the nuts in a safe place. You can put them in your pocket or anywhere but wherever you put it, always remember that you should not forget about them or put in a place where you can easily lose them.

Now, you need to remove the old filter. The filter may be round or rectangular in shape. Whatever the shape is, you will see that the filter will have lots of folded paper that is surrounded by rubber. Before you remove the old filter, you need to observe and remember how it sits in the housing. By doing this, you will be able to place the new filter correctly. To remove the filter, you need to pull it out carefully and make sure that nothing falls into the bottom of the box.

The next step is to put the new filter in place. When installing it, you need to be sure that you are putting it in the same configuration like the one you recently removed. The great thing about it is that even if you make a mistake, you will know about it as you won’t be able to get the top closed. Once you get the new filter in place, you also need to make sure to press the rubber gasket of the filter all the way into the groove of the housing.

The last step is driving off with a brand new air filter with the knowledge that you did it yourself and save a bit of money on the process. Installing a new air filter will usually take less 10 minutes. It is easy to do and you don’t need a lot of tools or even a vast knowledge or experience about car repair to do it.

Article sponsored by: www.jimmysautoservices.com